Nortel Networks 24T Manuel d'utilisateur Page 298
- Page / 310
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Using the BayStack 410-24T 10BASE-T Switch
E-4
309985-B Rev 00
Port Configuration (page 3-52) Unit 1
Status Enabled (for all ports)
LnkTrap On
Autonegotiation Enabled (for all ports
)
Speed/Duplex 100Mbs/Half (when
Autonegotiation is Disabled)
High Speed Flow Control
Configuration (page 3-54)
Unit 1 to 8 (depending on
configuration status)
Autonegotiation Enabled
Flow Control Disabled
Note:
The following two fields only appear when a single Phy
MDA with a separate redundant Phy port is installed.
Preferred Phy Right
Active Phy Read-only field indicating the
operational Phy port (Right,
Left, or None)
MultiLink Trunk Configuration (page 3-59) Trunk Members (Unit/Port) Zero-length string
STP Learning Normal
Trunk Mode Basic
Trunk Status Enabled
Trunk Name Trunk #1 to Trunk #6
MultiLink Trunk Utilization (page 3-61) Traffic Type Rx and Tx
Port Mirroring Configuration (page 3-64) Monitoring Mode Disabled
Monitor/Unit Port Zero-length string
Unit/Port X Zero-length string
Unit/Port Y Zero-length string
Address A 00-00-00-00-00-00
(no MAC address assigned)
Address B 00-00-00-00-00-00
(no MAC address assigned)
(continued)
Table E-1. Factory Default Settings for the BayStack 410-24T Switch
(continued)
Appears in this CI screen Field Default setting
- Using the BayStack 410-24T 1
- 10BASE-T Switch 1
- Trademarks 2
- Statement of Conditions 2
- USA Requirements Only 2
- European Requirements Only 2
- Taiwan Requirements 3
- Canada Requirements Only 3
- Contents 7
- 309985-B Rev 00 10
- Before You Begin 24
- Organization 24
- Text Conventions 25
- Acronyms 26
- Related Publications 27
- How to Get Help 28
- Chapter 1 29
- Front Panel 30
- 410-24T Switch 32
- Back Panel 34
- Features 37
- Security 41
- RADIUS-Based Network Security 43
- IEEE 802.1p 44
- IGMP Snooping Feature 44
- Flash Memory Storage 45
- MultiLink Trunking 46
- IEEE 802.1Q VLANs 47
- Port Mirroring 47
- 00-00-82-99-44-00 48
- 00-00-82-99-44-1F 48
- SNMP MIB Support 49
- SNMP Trap Support 49
- Network Configuration 50
- Segment Switch Application 52
- CPU PS1 PS2FAN 53
- Fail-Safe Stack Application 54
- Stack Operation 55
- BS41010A 56
- Base Unit 57
- Stack Configurations 59
- BS41011A 60
- IEEE 802.1Q VLAN Workgroups 64
- IEEE 802.1Q Tagging 65
- Shared Servers 72
- (Port Name is 76
- VLAN Workgroup Summary 77
- VLAN Configuration Rules 79
- IGMP Snooping 80
- IEEE 802.1p Prioritizing 85
- MultiLink Trunks 89
- Before Configuring Trunks 101
- 400-4FX MDA 103
- Chapter 2 115
- Figure 2-1. Package Contents 116
- Installation Procedure 117
- Caution: 118
- Connecting Power 126
- Cascade Module 127
- 100-240V 127
- 47-63Hz~ 127
- Redundant Power 127
- Verifying the Installation 128
- Initial Setup 131
- Figure 2-13. Main Menu 132
- Stack Setup 134
- Chapter 3 139
- Using the Console Interface 139
- Main Menu 142
- IP Configuration/Setup 146
- Choosing a BootP Request Mode 148
- BootP Disabled 149
- BootP or Last Address 149
- BootP When Needed 150
- BootP Always 150
- SNMP Configuration 151
- System Characteristics 153
- Switch Configuration 156
- MAC Address Table 158
- MAC Address-Based Security 160
- Screen 1 169
- Screen 2 169
- Screen 3 169
- Screen 4 169
- Screen 5 169
- Screen 16 173
- VLAN Configuration Menu 176
- Table 3-12 describes the 177
- Table 3-14 182
- Table 3-15. Reserved PIDs 183
- Port Configuration 190
- Table 3-19 describes the 191
- MultiLink Trunk Configuration 195
- Table 3-23 describes the 201
- Port Mirroring Configuration 202
- Table 3-24 describes the 203
- Table 3-25. Monitoring Modes 205
- Rate Limiting Configuration 206
- IGMP Configuration Menu 209
- Table 3-29 describes the 215
- Port Statistics 216
- Renumber Stack Units 227
- Hardware Unit Information 229
- Spanning Tree Configuration 229
- TELNET Configuration 237
- Software Download 240
- Download screen 241
- Configuration File 244
- Display Event Log 247
- Excessive Bad Entries 248
- Write Threshold 248
- Flash Update 249
- Reset to Default Settings 252
- Chapter 4 257
- Troubleshooting 257
- Interpreting the LEDs 258
- Warning: 260
- Normal Power-Up Sequence 261
- Port Connection Problems 262
- Software Download Error Codes 264
- Appendix A 267
- Technical Specifications 267
- Physical Dimensions 268
- Performance Specifications 268
- Data Rate 269
- Interface Options 269
- Safety Agency Certification 269
- Electromagnetic Emissions 269
- Electromagnetic Immunity 270
- Declaration of Conformity 270
- Appendix B 271
- Media Dependent Adapters 271
- 400-4TX MDA 272
- 100BASE-FX MDAs 273
- 400-2FX MDA 274
- Installing an MDA 276
- Appendix C 279
- Quick Steps to Features 279
- Off-page reference 280
- On-page reference 280
- Appendix D 289
- MDI and MDI-X Devices 290
- Appendix E 295
- Default Settings 295
- Appendix F 303
Produits connexes et manuels pour Mise en réseau Nortel Networks 24T
(14 pages)
(86 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels