Nortel-networks Mediant TP-1610 SIP Manuel d'utilisateur Page 193
- Page / 280
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Mediant 2000 SIP User’s Manual B. The BootP/TFTP Configuration Utility
Version 4.4 193 July 2005
B.10 Setting the Preferences
The Preferences window, Figure B-3, is used to configure the BootP Tool parameters.
Figure B-3: Preferences Screen
B.10.1 BootP Preferences
ARP is a common acronym for Address Resolution Protocol, and is the method used by all
Internet devices to determine the link layer address, such as the Ethernet MAC address, in order
to route Datagrams to devices that are on the same subnet.
When ARP Manipulation is enabled on this screen, the BootP Tool creates an ARP cache entry
on your computer when it receives a BootP BootRequest from the VoIP gateway. Your computer
uses this information to send messages to the VoIP gateway without using ARP again. This is
particularly useful when the gateway does not yet have an IP address and, therefore, cannot
respond to an ARP.
Because this feature creates an entry in the computer ARP cache, Administrator Privileges are
required. If the computer is not set to allow administrator privileges, ARP Manipulation cannot be
enabled.
• ARP Manipulation Enabled: Enable ARP Manipulation to remotely reset a gateway that
does not yet have a valid IP address.
If ARP Manipulation is enabled, the following two commands are available.
• Reply Type: Reply to a BootRequest can be either Broadcast or Unicast. The default for
the BootP Tool is Broadcast. In order for the reply to be set to Unicast, ARP Manipulation
must first be enabled. This then enables the BootP Tool to find the MAC address for the
client in the ARP cache so that it can send a message directly to the requesting device.
Normally, this setting can be left at Broadcast.
- User’s Manual 1
- Table of Contents 3
- List of Figures 8
- Mediant 2000 SIP 10
- List of Tables 10
- Trademarks 12
- Customer Support 12
- Related Documentation 12
- 1 Overview 13
- 1.1 Available Configurations 14
- 1.2 SIP Overview 15
- 1.3 Mediant 2000 Features 15
- 1.3.4 Supported SIP Features 16
- 2.1 General 19
- 2.3 The TP-1610 Board 20
- 2.3.1 Board Hot-Swap Support 21
- 2.3.1 on page 21 23
- 2.4 Rear Transition Module 24
- 2.5 Optional CPU Board 25
- 3.1 Unpacking 27
- 3.2 Package Contents 27
- Electrical Earthing 31
- RJ-48c Connector and Pinout 32
- 1 2 3 4 5 6 7 8 33
- 4 Getting Started 35
- 5 Web Management 39
- 5.4 Password Control 40
- 5.7.1 Main Menu Bar 42
- 5.7.2 Saving Changes 43
- 5.8 Protocol Management 44
- 5.8.2 Advanced Parameters 45
- 8.6 on page 146 49
- 5.8.4.4 on page 54 49
- 5.8.4.3 Internal DNS Table 53
- 5.12 on page 53
- 5-5: Trunk Group Table 59
- 5-6: Channel Select Modes 61
- 5.9 Advanced Configuration 62
- 5.8.5 on page 55) 65
- 5.9.6 Regional Settings 70
- 5.10.1 Gateway Statistics 71
- • DNS Disable 73
- • DNS Resolved 73
- • DNS Unresolved 73
- 5.10.4 System Information 77
- 5.11 Software Update Menu 78
- 5.11.2 Auxiliary Files 82
- 5.12 Save Configuration 84
- 5-38: Reset Screen 85
- 6.1 Secured ini File 87
- 6.2 Modifying an ini File 87
- 6.3 The ini File Content 88
- 6.4 The ini File Structure 88
- 6.5 The ini File Example 89
- [NTP UTC Offset] 93
- 6.7 SNMP Parameters 98
- 6.12 Channel Parameters 128
- Version 4.4 129 July 2005 129
- Web Parameter Name 129
- Version 4.4 131 July 2005 131
- 7 Configuration Files 135
- 7.3 Voice Prompts File 137
- 8-1: Calling Name (Display) 139
- 8-2: Redirect Number 139
- 8.3 ISDN Overlap Dialing 140
- 8.4 Using ISDN NFAS 141
- 8.6.4 Relevant Parameters 147
- 8.7.2 Call Transfer 147
- 8.8 TDM Tunneling 149
- 8.9 Call Detail Report 151
- 8.11 SIP Call Flow Example 153
- 8.13.1 SIP2PRI Gateway 158
- 8.13.1.4 Transfer 161
- 8.13.3 DTMF Configuration 163
- 9 Diagnostics 165
- 9.2.1 Syslog Servers 166
- 9.2.2 Operation 166
- 10 BootP/DHCP Support 167
- 10.2 DHCP Support 169
- 10.3 BootP Support 169
- 11 SNMP-Based Management 171
- 11.1.2 SNMP MIB Objects 172
- 11.3 Cold Start Trap 173
- Measurements 174
- 11.6 SNMP Interface Details 177
- 11.6.2 Trusted Managers 178
- 11.6.3 SNMP Ports 179
- B.2 An Overview of BootP 189
- B.3 Key Features 189
- B.4 Specifications 190
- B.5 Installation 190
- Log Window 191
- B.9 Log Window 192
- B.10.1 BootP Preferences 193
- B.10.2 TFTP Preferences 194
- B.11.1 Adding Clients 195
- B.11.2 Deleting Clients 196
- B.11.4 Testing the Client 196
- B.11.6 on page 198 197
- Allocation 201
- D.1 Fax/Modem Settings 203
- Interface 207
- F.4 on page 209
- 6.2 on page 87 209
- 5.6 on page 41) 209
- 7.2 on page 137 215
- 6.1 on page 87 217
- G.2 PSTN Trace Utility 220
- H.6 Abort Procedure 225
- Appendix J SS7 Tunneling 231
- J.2 SS7 Characteristics 232
- J.3 SS7 Parameters 233
- J.4 SS7 Table Parameters 234
- J.4.2 SIGTRAN Interface IDs 235
- J.4.3 SS7 Signaling Link 236
- Version 4.4 239 July 2005 239
- J.6.1 Table Indices 242
- J.6.2 Table Permissions 242
- Card Application 245
- K.3 Supported Architecture 246
- K.4 Implementation 247
- K.4.2 Call Flow Description 248
- K.6 Configuration Parameters 249
- K.8 RADIUS Server Messages 253
- K.9 Voice XML Interpreter 254
- <disconnect> 256
- Version 4.4 257 July 2005 257
- Version 4.4 259 July 2005 259
- K.11.1 Voice Prompts 260
- K.11.2 VXML Flow Chart 262
- Version 4.4 263 July 2005 263
- Version 4.4 265 July 2005 265
- K.12 VXML Script Example 266
- Version 4.4 267 July 2005 267
- Version 4.4 269 July 2005 269
- Appendix L SNMP Traps 271
- L.1.4 Other Traps 276
- L.1.5 Trap Varbinds 276
- Declaration of Conformity 277
- Industry Canada Notice 278
- Digital Device Warnings 278
- FCC Statement 278
- Original 279
- CD or Web site 279
- AudioCodes Offices 280
Produits connexes et manuels pour Matériel Nortel-networks Mediant TP-1610 SIP
(60 pages)
(2 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.033 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels